Features:
2 Channel Oscilloscope + Digital multimeter + arbitrary waveform generator
Oscilloscope: 70MHz Bandwidth with 2 Channels
Digital Multimeter: AC/DC voltage, AC/DC current, resistance, break, capacitance, and diode function
Arbitrary Waveform Generator: 0~10MHz Output, Sine, Square, Ramp, Pulse, Noise, etc
320*240 TFT Display, 5200mAh Lithium Battery,Over 24 Hours Cruising Ability
Auto-scale function
Ships with 2 oscilloscope probes and 2 BNC to 2 alligator clip test lead sets
The HANTEK2D72 is an all-new 70 MHz handheld oscilloscope from Hantek featuring a compact and lightweight design with a new generation of 3-in-1 multifunction tester that offers an oscilloscope, signal source and multimeter. It has a small form factor that is easy to hold in one hand and it has a stand that was designed to support multi-angle viewing adjustment. Ultra-low-power design with a Type C charging interface affords a full day or standbytwo months 2 hours battery charge allow working one full day of us or a standby time of two months. It also has a High-definition color LCD screen with a nice clear display with a simple easy to operate Minimalist keyboard design.
Specification:
Specifications
Aquisition Channel OSC+ DMM + AFG
Bandwidth 70MHz
Sample Rate 250MSa/s
Mode Normal, Peak Detect,
Average N acquisitions, all channels simultaneously, N is selectable from 1-128
Input Input Coupling DC, AC, GND
Input Impedance Resistance: 1MΩ; Capacitance: 25pF
Probe Attenuation Factors 1X, 10X, 100X, 1000X
Maximum Input Voltage 200Vpk (DC + peak)
Horizontal Scanning Speed Range(Sec/Div) 5ns/div ~ 500S/div (1-2-5 sequences)
Delay Time Accuracy ±50ppm (any interval ≥1ms)
Wave form Interpolation Step, Linear, Sin(x)/x
Memory Depth(Sample Points) 6k
Vertical A/D converter 8 bit resolution
Vertical Scale(Volt/div) Range 10mV ~ 10V/div @ x1 probe
100mV ~ 100V/div @ x10 probe
1V ~ 1000V/div @ x100 probe
10V ~ 10KV/div @ x1000 probe
Position Range ±4division
Selectable Analog Bandwidth Limit(typical) 20MHz
Lower Frequency Response(-3dB) ≤ 10Hz (at input BNC)
Rise Time at BNC(typical) ≤7ns
DC Gain Accuracy ±3%
Trigger Trigger Source CH1, CH2
Trigger Mode Auto, Normal and Single
Trigger Type Edge trigger, Alternate trigger
Trigger Sensitivity 0.02 div increments
Trigger Level Range ±4V
Input Input Coupling DC, AC or GND
Input Impedance, DC coupled 1MΩ ±2% for 20pF ± 3 pF
Probe Attenuation 1X, 10X
Max. Input Voltage CAT I and CAT II: Installation type: 300VRMS(10×)
Signal Source Mode
Waveform Impedance DC~10MHz
DAC Clock 2K~100MHz adjustable
Frequency Resolution 0.1%
Channel Count 1CH Waveform Output
Waveform Depth 4KSa
Waveform Range ±3.5V Max.
Meter Mode Maximum Resolution 4,000 Counts
DMM Testing Modes Voltage, Current, Resistance, Capacitance, Diode & Continuity
Maximum Input Voltage AC: 400V, DC: 400V
Maximum Input Current AC: 10A, DC: 10A
Input Impedance 40 MΩ
Measurement Range Accuracy Resolution
DC Voltage 400.00mV ± (0.8% + 5) 100uV
4.000V 1mV
40.00V 10mV
400.0V 100mV
600.0V ± (1% + 2) 1V
Overload protection: 400mV: 250V, other: 600Vrms.
AC Voltage 4.000V ± (1.2% + 5) 1mV
40.00V 10mV
400.0V 100mV
600.0V ± (1% + 2) 1V
Frequency: 40Hz~400Hz;
Frequency of 400V and 600V: 40Hz~100Hz
DC Current 40.00mA ± (1% + 2) 10uA
200.0mA ± (1.5% + 2) 100uA
4.000A ± (1.8% + 2) 1mA
10.00A ± (3% + 2) 10mA
Overload protection:
self restoring fuse: 200mA/250V, 4A and 10A range no fuse.
AC Current 40.00mA ± (1.3% + 2) 10uA
400.0mA ± (1.8% + 2) 100uA
4.000A ± (2% + 3) 1mA
10.00A ± (3% + 5) 10mA
Frequency: 40Hz~400Hz
self restoring fuse: 200mA/250V, 4A and 10A range no fuse.
Resistance 400.0Ω ±(1% + 3) 0.1Ω
4.000KΩ ±(1.2% + 5) 1Ω
60.00KΩ 10Ω
400.0KΩ 100Ω
4.000MΩ 1KΩ
40.00MΩ ± (1.5%±3) 10KΩ
Overload protection: 220Vrms
Capacitance 40.00nF ±(3% + 5) 10pF
400.0nF 100pF
4.000uF 1nF
40.00uF 10nF
100.0uF 100nF
Overload protection: 220Vrms
Diode 0V~2.0V
On-Off <50Ω
General Features
Display 320*240 TFT LCD
Interface USB Device
Voltage DC Input: 5V, 5200mAh Lithium Battery
Size 7.83" x 3.86" 1.61" / 199 X 98 X 41 (mm)
Weight 10.85 oz / 0.3kg
Included accessories
2 oscilloscope probes
2 BNC to 2 alagator clip test lead sets
1 DMM test lead set
1 USB Charging/Data Cable
1 USB Charger (110V AC Input)
1 Users Manual/Support Software on CD-ROM
